 |
|
 |
| The MPI-806H is an AC/DC open frame ATX switching power supply that can be configured as either 60 watts convection cooling or 80
watts forced air-cooling AC/DC switching power supply. The MPI-806 switching power supply features universal input, ATX output (3V/5V/12V/-12V/+5V stand-by), utilizes thermally efficient U-channel
chassis and has no noise quality. The MPI-806H is designed for use with ultra quiet, low power consumption applications such as low power digital media device based on VIA EPIA M-Series Mini-ITX
Main-board or for Industrial grade applications, DVR, gaming machines and embedded System applications. |
| Read full detail |
Download full specification |
| Availability |
In stock |
| EMAIL US FOR A QUOTE |
|
|
- 60W convection cooling, 80W with 8.6 CFM forced air cooling
- Universal input and 3.3V/5V/12V/-12V DC outputs, 5V Stand by
- Open frame, thermally efficient U-channel design
- Rated at 50 °C
- PG/PF signal available
- Remote On/Off
- 100% 50 °C burn-in
- MTBF>130,000 hr. at 50 °C, Mil-217F.
- Designed for Industrial and Embedded System Applications.
- Two years warranty
|
| Input Type |
AC |
| Input Voltage |
90-264 VAC continuous input range |
| Input Frequency |
47-63 Hz |
| Input Current |
2A @ 115VAC, 1A @ 230VAC |
| Inrush Current |
30A @115VAC, 60A @ 230VAC |
| Outputs |
+5V |
+3.3V |
+12V |
-12V |
+5Vsb |
| Minimum Output Current |
1A |
0A |
0A |
0A |
0A |
| Rated Output Current |
5A |
4A |
1.5A |
0.5A |
0.75A |
| Maximum Output Current |
8A |
6A |
3A |
- |
- |
| Line Regulation |
1% |
1% |
1% |
1% |
1% |
| Load Regulation |
2% |
4% |
4% |
5% |
4% |
| Ripple and Noise (peak to peak) |
50 mV |
50 mV |
120 mV |
120 mV |
120 mV |
| Efficiency |
> 70% |
| MTBF |
130,333 hours at 50 °C |
| Power On/Off |
The power supply will be turned on when the power On/Off pin is connected to secondary GND. |
| Power Good Signal |
When power is turned on, the power good signal will go high 100 ms to 500 ms after all output DC voltages are within regykation limits. |
| Power Fail Signal |
The power fail signal will go low at least 1 ms before any of the output voltages fall below the regulation limits. |
| Overload Protection |
Fully protected against output overload and short circuit. Automatic recovery upon of overload condition. |
| Safety |
| 60950 3rd edition |
| CB |
| IEC 60950-1 |
| TUV |
| EN 60950-1:2001 |
|
| EMS |
| IEC61000-4-2, 8KV air discharge and 6KV discharge 3 Level |
| IEC61000-4-3, 3V/M 2 level |
| IEC61000-4-4, 2KV line & PE 3 level |
| IEC61000-4-5, 2KV 3 level |
| IEC61000-4-6, 10V 3 level |
| IEC61000-4-8, 10A/M, 3 level |
| IEC61000-4-11 |
|
| Radiation/Conduction |
EN 55022/ CISPR 22 & FCC Part 15 Class B |
| Operating Temperature |
0~50 °C at full load, de-rate linearly above 50 °C by 2.5% per °C to maximum temperature at 70 °C |
| Storage Temperature |
-40~70 °C |
| Altitude (max) |
up to 10,000 ft |
| Width x Length x Height |
128x81x40 (mm) |
|
|
| |
| MPI-806H |
60W fanless ATX AC/DC switching power supply |
| Cable (No. 866-806H) |
ATX connector, HDD connector x 2, FDD connector x 1 |
|
| |
| MPI-810H |
85W fanless ATX AC/DC switching power supply |
| MPI-815H |
150W fanless ATX AC/DC switching power supply |
|
|
|
|
